What is EPIRB ?

What is EPIRB ?

rescueME EPIRB

Emergency Position Indicating Radio Beacon or EPIRB is used to alert search and rescue services in the event of an emergency. It does this by transmitting a coded message via the free to use, multinational Cospas Sarsat network. A 406 MHz distress frequency signal is sent via satellite and earth stations to the nearest rescue co-ordination centre.

EPIRBs also transmit a homing signal via 121.5 MHz to help rescue services to pinpoint the beacons location. Some EPIRBs also have built-in GNSS receivers which enables the rescue services to accurately locate your coordinates to 50 metres.

According to IMO update rules , an EPIRB also have  included an AIS , which allows vessels in the local area (4NM) to pick up the distress alert as an ‘Man overboard’ alarm on their vessels AIS screen.

Over 56,000 lives saved…

The Cospas-Sarsat Programme has helped save over 56,000 lives since its launch in 1982.  Aviation, marine and outdoor enthusiasts rely on 406 MHz emergency beacons to help with their detection and location in a distress situation around the world.

Who need EPIRB ?

EPIRBs are generally installed on marine vessels and are typically registered through the national search and rescue organization to that specific boat.  Some vessels have a dedicated vessel EPIRB and a secondary crew EPIRB which goes into a lifeboat with the crew. In most countries EPIRBs are mandated to be used in all commercial shipping, fishing vessels and racing sailing vessels. However, they are also widely used on yachts, leisure boats and kayaks.

The differences between EPIRBs and PLBs

Personal Location Beacons work in exactly the same way as EPIRBs by sending a coded message on the 406 MHz distress frequency which is relayed via the Cospas-Sarsat global satellite system and utilising 121.5 MHz and Multi constellation GNSS to pinpoint location.

However, there are a number of differences between them. PLBs are designed to be carried on the person so they are much smaller. PLBs are designed to be used anywhere in the world, on the sea and also on land. Unlike EPIRBs not all PB’s float but may come with an additional flotational sleeve which they should be carried in.

PLBs, once activated, will transmit for a minimum of 24 hours and stored for 6 years; while the battery life on an EPIRB is typically ten years with at least double (a minimum of 48 hours) the transmission period.

An EPIRB is registered to a vessel, whereas a PLB is registered to a person. This means that if you are crewing a yacht and you switch to a new yacht the plb is still correctly registered; however, if you have an EPIRB and buy a new yacht you will need to re-register it when installing in your new boat.

Legally, unlike EPIRBs, PLB’s cannot by designed to be automatically activated. This is due to the fact they are more mobile and therefore more likely to be dropped or handled. An automatic activation feature on a smaller device would increase the likely hood of accidently activated, with the associated cost and risk to the search and rescue services. As PLB’s don’t have water activation switches they don’t have the magnetic collar used by EPIRBs to prevent accidental activation.

Finally, PLB’s have a three-stage activation process, this is again to prevent inadvertent activation.

 

How do I register my EPIRB?

Once you have purchased your EPIRB you need to register it in your country. You need to provide contact information plus information about the vessel it is to be used on. This is vitally important because if the EPIRB is activated the search authorities in your country will try to make contact with you or other people you have listed to enable them to see if a rescue is required.

In the USA registration is through NOAA (National Oceanic and Atmospheric Administration).

For more information about where and how to register your EPIRB please contact your local supplier.

 

April 6 was 406 Day- a national campaign run by NOAA to spread awareness of the importance of emergency position indicating radio beacons, or EPIRBs, and personal locator beacons, or PLBs, in boating safety.

 

In 2018, the Eighth Coast Guard District responded to over 200 distress signals from EPIRBs aboard aircraft and boats.

An EPIRB works by transmitting a signal that is picked up by a satellite and then relayed to a rescue coordination center.

Beacon registration is free, easy, and required by law. Federal law requires all EPIRBs be registered in the NOAA SARSAT Beacon Registration Database, which is free to all beacon owners.

When beacon owner information changes, it should be updated online at www.beaconregistration.noaa.gov or by contacting the NOAA SARSAT Beacon Registration Database at 1-888-212-SAVE (7283).

Owners are required to validate their beacon information every two years to ensure their contact information is up-to-date. Current beacon owner information allows search and rescue responders to work more efficiently and can decrease response time during distress situations.

If your EPIRB is accidentally activated, contact the U.S. Coast Guard at 1-855-406-USCG (8724) and provide them with the beacon’s ID to cancel the false alert.

Search and rescue personnel begin responding immediately to every activation of a distress beacon. Cancellation of false alerts helps protect SAR personnel who would be utilized during an actual emergency, and ensures valuable resources are available to respond to actual distress cases.

“The Eighth Coast Guard District covers roughly half of the Gulf of Mexico and receives over 200 EPIRB alerts a year,” said Kevin Robb, a SAR specialist at the Eighth Coast Guard District. “Approximately 97% of these alerts are false alerts, including accidental activations and bracket failures. Our sole focus is your safety on the water. Keeping your EPIRB registration information accurate helps us to better respond to your situation, and in turn prevents us from unduly hazarding our first responders and wasting resources at taxpayer expense. Be safe and register your EPIRBs and PLBs and keep the registration information current.”

 

1 The process begins with the activation of a distress beacon (EPIRBs for maritime use, PLBs for personal use and ELTs for aviation use) in an emergency situation,
sending out a 406MHz signal.
2 The Cospas-Sarsat satellite system picks up the signal and transmits it back to a ground receiving station on earth — these are called Local User Terminals or LUTs.
3 The LUT processes the signal to generate a distress alert and relays it to a Mission Control Centre.
4 The Mission Control Centre receives the alert and relays this with location information to a Rescue Coordination Centre, often looking up the unique beacon ID number to gather information about the registered owner.
5 The Rescue Coordination Centre alerts the appropriate emergency response teams to deploy a rescue effort

 

 

About IMARINEX

Imarinex One-stop ship communication and navigation supplier, originating from China, serving the world.

Share This Page
Get A Free Quote
Contact Form Demo (#3)
Scroll to Top

Get A Free Quote Now !

Contact Form Demo (#3)
Scan the code